Search the Community

I installed a Hopkins wiring kit to my 2016 Chevy Equinox for towing purposes. That was in 2017. I worked fine until about six months ago. Now I only get the "parking" or "running" lights on the toad and not signal or brake light. I have tested the tow bar pig tail and am getting running, left/right turn signal and flashed and brake lights. But when I plug it into the Toad, only the "parking" or "running" lights are on....no signal, or brake, either side.

Planning the installation of ground effects LED light strips to surround the lower exterior of my motorhome and wondering if others here have done the same and can share information on the following; 1) if your installation includes the use of a RF remote to turn the LEDs on/off, where did you install it?, i.e. on the exterior of the motorhome such as in the electrical bay or inside the basement area, or on in the interior of motorhome, and how well would you describe how well the RF remote works (signal is good, fair, poor), same question applies if you installed colored LEDs and use a bluetooth/RF remote. 2) if you installed an in-line On/Off switch to control power to the LEDs where did you place it? inside the motorhome in or under the dash, in the basement area, etc. 2) did you direct connect to your motorhome's 12-volt DC current or use a 120 volts AC converter? 3) if you ran LED light strips around the entire underside of the motorhome, how many junction boxes/pole terminal connectors did you use to gather/consolidate the various power leads from each LED strip into a pair of common power wires (+/-) to tie into the converter? 4) have you had problems with the lights since installing them and if so, what were they? Needless to say, I'm planning a DIY'er installation and have a fairly good view of how I need to do it, just felt that by asking other FMCA members here who've done their own installations (or had their's done), some additional insight would be helpful. ps - please don't "bash"...Im doing a simple soft white installation that will simply serve to add additional exterior lighting downward toward the ground when parked/docked remotely. The LEDs will not be visible from the sides of the motorhome. Any/All answers will help.

Sharing photos of my recent DIY installation of Boogey Lights "Under Glow" surround ground effects LED lighting. As shown, the LEDs were installed beneath the motor coach on all sides (F&R, Driver and Passenger sides including underneath the entrance door steps). Installation is relatively simple and easy to do but does require some pre-planning in terms of placement and wiring. I choose to direct wire my LEDs to the coach' 12vDC circuitry which is Boogey Lights recommended practice (in lieu of using a 110vAC converter which are available). Located the main junction box and LED controller inside the passenger/door side basement compartment just ahead of my wet tank basement and then ran a single 14-AWG power (Pos +) wire to my electrical bay located on the driver's side and connected to a spare fuse terminal on the main 12vDC fuse panel together with the use of a 20-amp fuse. Materials required for the installation included 1) Boogey Lights (basic) RV Under Glow kit (which includes 2-ea 16' pre-measured LED lighting strips, a controller and wiring accessory kit) together with additional pre-measured LED light strips in 8', 4' and 3' sections along with their optional HD-M7 RF controller, aluminum channel extrusions (for mounting the LEDs strips as well as the light diffusers panels which "snap on" to the aluminum channel housing the LEDs), 2) additional materials and supplies used for my DIY installation which included 16 AWG wire, tie-wraps, #8 self tapping screws, black RVT silicone, some 3/4" x 3/4" x 8ft aluminum angle extrusions as well as some 1/4" x 1" x 8 ft. aluminum flat bar) along with other misc. parts and supplies. As shown, I particularly selected Boogey Lights single color "soft white" LEDs while they do offer a multi-color version (basically R,B,G which along with their optional controllers can be "tuned" to produce millions of color variations if so desired and can also be controlled by their cell phone app). I also upgraded to their HD-M& RF controller that includes a dimming feature (as well as other lighting control features) which further allows me to adjust the LED lighting illumination to align/match with my existing OEM installed LEDs located beneath the 2-two passenger side slides as well as on my 3 Girard Canopy Awnings. Used with discretion, these LEDs provide both lighting accent to the coach while at the same time offer increased safety when moving about the outside perimeter at night such as when needing to access the wet or electrical bays. Expectation is we will not "always" use these but on occasion do so while respecting the privacy of our fellow RV neighbors when in commercial parks. Additional information and photos of the actual installation can be found in at IRV2.com under RV Forums > RV Systems and Tech > Gear Discussions; http://www.irv2.com/forums/f52/diy-installation-of-ground-effects-led-lighting-374831.html I'd like to also mention and recommend Boogey Lights if your interested or contemplating a similar installation yourself. Boogey Lights Inc. is widely recognized as a supplier of high quality (and not the cheapest) LEDs particularly for recreational use applications, i.e. Automobiles, Motorcycles, Boats & RVs. The material composition and quality of their lights are apparent when you see them and even more so when you install and use them. They also offer the best warranty in terms of the lights themselves and are available to provide assistance (by phone or email) when it comes to planning or actually installing them. Don''t second guess yourself - you can easily "do it yourself (DIY)". No rocket science involved but does require that you do some "pre-planning" as to (a) where you want to install them, (b) what type of lights you want (single or multi-color), (c) the lengths of LED lighting you'll need or want, (d) where you will mount your controller (e) and whether you want to do direct 12vDC or use a 110v AC adapter - then its all a matter of labor from that point forward. On a coach the size of mine (45' DP) it was some what a labor of love that lasted more than 10-days to complete (albeit when I work for myself, I tend to call it a day and come and go as I please), hence the installation could have been quicker, I just wanted to take my time and work on them when I felt like it. Why DIY one might ask (vs. having them done for you)?, Well I obtained numerous quotes that ranged from $3,700 to as much as $4,500 for the supply and installation of the LEDs. By doing it myself I have calculated that my total cost (excluding my personal labor) was <$1,000 (which included the LEDs and supplied materials purchased from Boogey Lights at a total cost off $589.00). Hope you enjoy the photos.