Jump to content

jleamont

Members
  • Content Count

    6583
  • Joined

  • Last visited

  • Days Won

    6

Posts posted by jleamont


  1. 3 hours ago, fountaindavid.jean said:

    Has anyone had any success using Electronic Contact Cleaner and a "KNOWN" circuit/plug that seems to have intermittent problems??

    I have not. Tried several products and replacing the pins in the connector is where I always ended up.

    hopefully someone else can chime in with a successful story and product.


  2. 1 hour ago, Moonwink said:

    After researching brake systems extensively, I went with the ReadyBrake because it's fully proportional, easy and quick to connect and disconnect, doesn't require any power and there's no "box'  to install/remove.

    Great research! All of those very reasons are extremely important to us as well. Its shocking how many systems are not fully proportional.


  3. 10 hours ago, RSBILLEDWARDS said:

    Yea Joe but "your" mountains are really very different than the ones in my part of the country. Just sayin point of reference very different. Out here we do not see many small C types pulling toads. When they are they are usually slower going up hill.

     

    Bill, I ran them out west on many occasions with the old coach and a few times through the Allegheny mountains here from a dead stop, with toad on some back roads. On an interstate they will have momentum, I would usually loose that after a 2 mile pull. 


  4. I must admit I have tried several products over the years and this one has done us well, it’s not expensive and available at most automobile parts stores (chains).

    My wheels were so bad I bought a polishing cone for my cordless drill and applied it with that and buffed it off with a towel. Just be careful with any powered applicators, start off slow or the product will be all over you including your hair  :wacko::lol:

    EE0CA961-3AB1-47E8-BCE4-5BC9A71186E1.jpeg

    D33F4D7D-F0A9-48EF-9339-03AC3B8D053B.jpeg

    A1322A56-F073-454E-B711-B390EE3F28C1.jpeg


  5. larcar, have you considered swapping them out for LED? When we bought this coach it had several lights out inside and failed ballasts. I found it more cost effective to do an LED conversion at that time than fussing with the existing light bulbs and ballasts. 

    The LED strips were so bright I only needed one where there was two florescent bulbs.

    RV LED 1.jpg

    RV LED 2.jpg


  6. My DW keeps a spreadsheet rolling with all household expenses, the RV has two lines, one for the payment and one for parts etc. Fuel gets tracked via the credit card it went onto (just in case of a dispute), we don't usually track fuel once its put in the tank. I will run a MPG calculation off of the calculator in my phone and clear the trip odometer and its forgotten about. Receipts get tossed once the statement arrives and its checked for accuracy. 


  7. Closeenough, Welcome to the FMCA Forums!

    Are you comfortable with taking it apart and do you have a multimeter? If so watch this video, there is where I'd start. 

    be careful, those capacitors hold a voltage charge. 

    https://www.google.com/search?q=diagnosing+rv+a+c+capacitor&rlz=1C1CHBF_enUS854US854&oq=diagnosing+rv+a%2Fc+cap&aqs=chrome.1.69i57j33l2.12671j1j7&sourceid=chrome&ie=UTF-8#kpvalbx=_LuP0XtLGFsHF1QGOm46wBQ35

     


  8. renglish, Welcome to the FMCA Forums! 

    I use a much older version of this unit;

    https://www.amazon.com/Camco-40630-Evo-Water-Filter/dp/B012GHM3GS/ref=zg_bs_10806177011_34?_encoding=UTF8&psc=1&refRID=WZQ7QH35YDT1M39CYZB1

    I have used charcoal filters in the past and I have never experienced that issue before. I have had them clog and water pressure dramatically reduced. How old or long was the filter in service? 

     


  9. 53 minutes ago, F433921 said:

    It really messed up my routine while it was down.

    Funny how that all works out. Something that we all take for granted as being here, when its not it really messes up your daily routine. 


  10. On 5/27/2020 at 11:52 AM, wtbuck12 said:

    I noticed if I run my generator for an extended period, it drifts out a foot or so from the front of the MH. The slide opens and closes hydraulically and I can't find any kind of lock to keep it closed. Should the hydraulic cylinder keep it closed?


    Thanks for any input

    YES, it should stay closed. You have a leaking cylinder (internally) or a valve hanging slightly open. If you are capable of taking it apart, remove the pump and cylinder and take them to a hydraulic repair shop, they can test both and determine the cause, most will also be able to repair it. 


  11. nurseruth90, Welcome to the FMCA Forums! 

    Our manual calls out retracting the slides with severe weather. Now comes the part up to interpretation, whats severe weather? If the winds are over 25 mph in a storm we close them even if we are inside. 


  12. This is common on that chassis with 19.5 tires. The issue is the suspension is spring (not air) and the 19.5 tires have an very stiff side wall, some will argue that they are stiffer than a 22.5 since the construction is very similar BUT the wheel is much closer as the side walls are shorter. 

    As mentioned tire pressures and shocks will also play a part. Shocks if too loose it will porpoise and make you sea sick driving it. This could very well be the "nature of the beast' so to speak. Our last coach would break apart on a cross county trip, I was always replacing sheared off hardware somewhere on the body. The roads in the US are getting better but are still in poor condition.  

×
×
  • Create New...