hermanmullins

The last time I saw Rich, he and Tireman were relaxing having a Philly Cheese sandwich in Perry Georgia. Herman

Keith, The make of your Jacks would help. But here is what I would try first if the jacks are Hydraulic and you are good DIY. I would take the leaking cylinder off and take it to a Hydraulic Repair shop and have them reseal it. As many have said before google Hydraulic Repair Shops in the Yellow Pages in your area. Herman

Keith, Before calling a tech take a look at the Generator and make sure the Circuit Breaker isn't tripped. Herman

Nice information, it should help a lot of folks. Thanks, Herman

Carl, To my knowledge Wranglers only come in 4 X 4 and are as you said "put in neutral and go". The same with GMC and Chevrolet 4 X 4 vehicles. They have different ways of putting the transfer cases into 4 wheel neutral, but when in Neutral, GO. Friends that have had Fords say the same thing, put it into neutral and GO. (Of coarse on all, you do have to hook up first ). Herman

If you will go to the FMCA home page. click on the DASH BOARD, it is the speedo symbol on the right side of the page. When on the DASH BOARD click on MAGAZINE. there you will find the CLASSIFIED section. Herman

Haidenger, I have contacted FMCA Membership Manager and Dan will post here hopefully some answers to your concerns. Don't want to lose you. Herman

I have the Hopper with one Joey in our coach. Works just fine. With the Hopper you are able to connect up to tow Joeys and have High Def. on all sets. You will have a small sending unit next to the Hopper that require a 110 outlet. Dish sent out a tech and he did the install, no charge for us. Let me caution folks that when replacing one or more TVs to NOT replace them with the same Make. I have two VIZOs and the if you are not in just the right spot when you turn one one it will turn the other one off (same remote). However they both work interdependently form one another on the Dish remote, just not the off/on function . Herman

Sorry Bruce, I forgot. Been 3 vehicles (all Chevrolets) since I had the push buttons. Glad it worked out. Herman

Please, before you go too far with this rumor please contact the FMCA office and get the complete and true facts. Let me recommend doing this when ever you had doubts about any Benefit offered by FMCA. Hearsay is not good for you or anyone else for that matter. Thank you, Herman

Bruce, Set the Parking brake, start the engine, put the vehicle in neutral, put your foot on the brake pedal and then hold the 2 and 4H buttons down at the same time. It can take up to 15 seconds and the Red neutral light will come on. I would always then put it in drive and release the brake. I would then race the engine to make sure the vehicle is in neutral. Then put the transmission in Park, turn off the engine, release the Parking Brake, remove the key and lock the doors. If I am not mistaken the 01 doesn't have a steering wheel locking pin. Of course this is with the understanding that you have the vehicle hooked up to the RV. Herman

Dan, Even though your batteries are new make sure they are all fully charged and load test each one separately. Even though new, one may be bad. Just a thought. Herman

Brown, The drivers side map light on my 02 Dynasty is located on the top of my lamp, it is a twist top. I also have a overhead light on the drivers side and the switch is right next to my Park Brake Button. Herman

You signed up for 30 amp and you will have 30 amp service. Please come in with a FULL Water Tank and EMPTY Holding Tanks. Also have extra electrical cable. Some times you are right next to a power pedestal and some time you will need a bit more. Herman

First thing first. Welcome to the Forum. Before you arrive please have your Placards in the windshield of Your truck. This will allow the Parking crew to know where to park you. You will be required to unhook once you are parked and the Parker will show you where you can park your truck, it will be real close to where you are parked.. There are Trams to take you around to all of the Vendor, Show Coaches and Seminars. If when you arrive and have any questions find me and I will be happy to assist. I will be on a golf cart with SAFETY on the windshield. Just wave and I will stop. Also Welcome to the 97th FMCA Convention and RV EXPO. Herman

I have asked for the instructions for the app to be posted here. Dan should post for both Android and Apple. It should be here soon. Sorry I don't have an app, I am told what to do and where to be almost every minute. Herman

grampy, There is an app for Perry on Face Book. If I understand it you go on Face Book and look for FMCA Conventions. I will post the entire thing here after I get out of a meeting where I will get the information. Herman

LeRoy, welcome to the Forum. Do you have a truck dealer in Chilliwack? That would be the place I would start. They may be able to measure the Muffler and come up with one to fit your coach. It may be a Roadmaster Chassis. Sorry I can;t help on the Manual. Herman

Cdrifter99, IMHO I would find a Goodyear dealer in Tampa and have them order them in for you. The freight would be almost prohibited. A dealer should be able to get them from a warehouse. The dealer is a friend of mine, Ronnie Thomason of Thomason Tire 972-542-347, McKinney, TX. When I get tires from him, he will order them from a warehouse in Dallas, Texas. Herman

If it hasn't been said, Welcome to the Forum. My dead bolt stuck in the locked position one time. It turned out the extension of the bolt had a broken roll pin. I repaired the bolt and have never used the dead bolt. Herman

Same question and almost the same answer, from two different people and different years. All 2018 and 2001 Saturn. Herman

bounder, Go to the fmca.com home page, Click on Magazine and select TOWING Guide. There you will find the guide for 2001 vehicles. Herman

Xtreme Paint Graphics, Nacogdoches, Texas xtrenegrapjics.com 936-580-5888 Herman

Wiley, Welcome to the Forum. Might I suggest that you contact Monty at M&G Engineering. He is the General Manager and will be happy to assist you. 903-675-2812 montymg@live.com Herman

Ed, You might need to check the front wheel base. The flex may be wider than the Mini. I do remember the Mini having a wide foot print, just not sure if they are the same. Good Luck, Herman